CSD7 Servo Drive (EtherCAT Network type) User Manual Catalog Number(s): CSD7_**BN(F)1 Important User Information Solid state equipment has. CSD7 series servo drive have a various power range such as from W to 5KW. The CSD5 is a universal, stand-alone servo drive that can be used. CSD5 is a stand-alone type Servo Drive to use general purpose for overall factory The added features of CSD5 such as linear motor control solution and.
|Published (Last):||24 June 2011|
|PDF File Size:||15.11 Mb|
|ePub File Size:||14.53 Mb|
|Price:||Free* [*Free Regsitration Required]|
CSD5 Servo Drive User Manual
Additional Resources The following documents contain additional information concerning related CSD5 servo drive products. In case of a srvo that cannot be dealt with, please contact the company s technical support team or after-sales service center. Refer to the below flow chart to monitor the content of each monitor item. Refers to a controller or a device that gives command to the servo drive and controls it. If the following marks and contents of each mark are indicated in the contents of this user’s manual, you must be fully aware of them and follow them.
T1 T1 T2 T1: This is the method to remove resonance from the equipment by the resonance frequency detected automatically in real-time.
CSD5 Servo Drive User Manual |
Switched off Close 1: It is the signal for the brake control installed inside or outside of the servo motor. Used to apply a parameter, enter a function or move to the left digit.
Servo drive has self-diagnostic function. Instruction Manual Option Card for Frequency Divider Deliver this instruction manual without fail to those who actually operate the equipment.
Thus, be fully aware of the shape, name and function of icons. When the position error exceeds the position error value in [Ft Connect only one wire at wire inlet of the socket. Install the drive on the control panel which satisfies the IP54 protection.
Before You Begin Pay attention to the following precautions when wiring. A 2 Spin the Motor Use the proper wiring and grounding method to prevent any affects from the noise.
Parameter group 1 has gain setting parameter for tuning and it is classified as follows. To improve a transient response characteristics, we will explain gain setting for zervo, velocity and position control loop. When it is set to ON, limit the forward torque by the set value [Ft The following serbo the symbols used on the circuit diagram.
Safety instructions P3 2. Refer to the value set at the factory before the shipment.
Operate the system with no load during pilot operation. Describes the tuning to implement optimum performance of load system.
Maximum setting value of 0x Ft Oil and Coolant Circulating Heating System. Motor and encoder wiring has a wrong connection. The number of mapped objects is recorded in Sub-index 0 of the mapping table. Line Drive less than 3 [Mpps] For Open Collector 24 [V] pulse input, connect to this terminal without a pull-up resistance.
The character displayed the normal operation status does not flicker, but once the abnormality serbo for servo warning is sensed, the applicable character is displayed and flickers. B Important User Information Solid state equipment has operational characteristics differing from those of electromechanical. You can adjust gains related to torque in torque mode. Unit Specifications More information.
CSD5 Servo Drive. User Manual. Catalog Number(s): CSD5_xxBX1 – PDF
Wiring This chapter describes the wiring information for motor, host controller and other peripheral devices connected to the servo drive, along with the circuit diagram. It will also show the user how to. When the fault occurs, 3-digit fault code and 5-digit text message as shown in the below table are displayed by turns.
It will also show the user how to More information. Refer to the table below for the meaning of each display.
CSD5 Servo Drive. User Manual. Catalog Number(s): CSD5_xxBX1
Prepare the proper battery for specification. Describes brief functions of the product. It is classified into a parameter selected among already set values selected parameter and a parameter, which the users give appropriate value. Read this operation manual. To increase cooling efficiency, be sure to install the product vertically. Be sure to install the product vertically Install the Servo Drive Vertically The CSD7 series servo drive adopts a forced cooling method using the fan installed inside the product.