KEMPEROL 2K-PUR is a two-component, UV-stable high performance seamless and self-terminating cold fluid-applied polyester reinforced solvent-free. KEMPEROL 2K-PUR Speedshot combined with KEMPEROL 2K-PUR is the ideal solution for all applications where speed is essential. These include balconies. KEMPEROL® 2K-PUR is a solvent-free and odourless, fully reinforced, polyurethane resin-based liquid waterproofing system. It is ideal for use on sustainablility.
|Published (Last):||10 January 2017|
|PDF File Size:||12.40 Mb|
|ePub File Size:||14.2 Mb|
|Price:||Free* [*Free Regsitration Required]|
Cold applied wet-on-wet, without the fire risks of hot works, it bonds directly to virtually any substrate to provide a seamless, elastomeric, UV-stable membrane that is equally suitable for both new-build or refurbishment projects such as roofs, podiums, balconies and terraces, is root resistant and suitable to receive a variety of finishes including green roofs. Supports for electrical conduit and gas lines 1 inch or less in diameter, and bases for lightning protection rods and cable, can be adhered directly to the membrane surface with a single-component, polyurethane construction adhesive.
KEMPEROL® 2K-PUR Liquid Applied Solvent-Free and Odourless Waterproofing – Cold Roof System
Follow cap sheet manufacturer’s recommendations for the appropriate asphalt application rate and application procedure. Not found what you’re looking for? Apply primer only up to the edge of the membrane flashing terminations.
Cover all terminal edges with the filter fabric flap by tucking the kempegol behind the core. Mix and apply two-component primer in strict accordance with written instructions of Membrane Manufacturer.
Provide barricades, retaining ropes, safety elements and any appropriate signage required. White spots are indications of unsaturated fleece or lack of adhesion. Allow the surfacing mix to self-level and reach an initial set for minutes until material will retain a peak after being touched by a finger.
Control or expansion joints in excess of 2 inches in width and all expansion joints subject to vehicular traffic require the use of a separate engineered joint system.
Smaller areas shall receive a minimum of 3 tests. Metal flashing flanges to which membrane is to be bonded shall be a minimum of 4 inches in kemperok, and secured to the substrate or wood nailers 6 inches on center staggered with fasteners appropriate to the substrate type.
California Waterproofing Supply Kemperol 2K-PUR
It is ideal for use on sustainablility based projects ;ur on sensitive occupied buildings where the strong odours and fumes from solvent-based products could be disruptive.
Tape fabric overlaps, and seal butt joints with tape as well. Alternatively, replace all broken or damaged parts of existing drains and scuppers. Electronic Field Vector Mapping EFVM test shall be completed prior to the installation of the overburden, but after the membrane receives a final inspection. Knead primer Component B into Component A and mix the components for approximately 1 minute.
Reference FM approvals for fastening patterns to satisfy FM wind uplift requirements. Tests shall include tensile bond strength and moisture content of substrate. The correct amount of resin will leave no whiteness in fleece and there will be a slightly fibrous surface texture. Areas of soft or scaling brick or concrete, faulty mortar joints, or walls with broken, damaged or leaking coping kmperol be repaired in accordance with the requirements of the Architect and Waterproofing Manufacturer.
Substrate surface must be dry, with any remaining dust or loose particles removed using clean, dry, oil-free compressed air, industrial vacuum, cloth wipe or a combination of methods. Go to Supplier website.
KEMPEROL 2K PUR
Kemper System America, Inc. Granule-surfaced membrane shall have all loose granules removed from the surface by vacuuming and power brooming.
Fill cavities with a patching mixture of primer and approved kiln-dried sand in a 1: Highly durable and long lasting Weather resistant after 30 minutes Suitable for normal maintenance foot traffic. Adhering to gypsum-based panels, cementitious stucco, synthetic stucco, wood or metal siding, and other similar materials is not acceptable. Additive specifically designed to accelerate the resin reaction time at ambient temperatures below 50 degrees F 10 degrees C.
A wire brush finish is not acceptable. Place the boards onto the pjr adhesive beads. At roof penetrations, cut the drainage core around the protrusion, cut an X in the fabric, and tape the fabric around the protrusion to prevent intrusion of overburden materials into the core. Upon completion of waterproofing and flashings and associated work, institute appropriate procedures for surveillance and protection of roofing during remainder of construction period.
Ejot Srbija -specijalista u tehnologiji povezivanja. KEMPEROL 2K PUR
Review and 2j schedule related to waterproofing work and verify availability of materials, installer’s personnel, equipment and facilities needed to make progress and avoid delays. Note that tapered insulation requires cover board.
UK Rest of the world.